How to Replace a Caravan Roof Hatch

Share on facebook
Share on twitter
Share on linkedin
Share on email

Roof hatches can be easily damaged or like anything fitted to the roof of a caravan, eventually prone to water leaks.

The hatch pictured here is on a motor-home, but the principle is the same for a caravan, the only difference being that here we’ve got a 1.2mm-thick sheet metal roof and on a caravan it’s typically a 0.7mm-thick aluminium roof.

The hatch unit itself here is the type with an integral exhaust/inlet fan, but for the purposes of hatch replacement there’s no difference between this and a standard non-fan hatch except for the need to hook up two wires in this case.

This hatch had a couple problems that caused it to allow water to leak through. The plastic frame had cracked in two spots and the foam seal used was intended to take up the gaps caused by the ribs in the roof panel but it actually worked as a membrane trapping water. Both problems eventually allowed water through, staining the ply panelling inside. Luckily it was caught fairly early, or the time-consuming (and expensive) job of replacing rotted interior ply would have been added to the job card.

Getting up on the roof of a caravan can end up in disaster, and that’s not just if you were to fall off.

1. REMOVE THE OLD HATCH

Removing the old hatch

First the screws securing the hatch to the roof are removed. Then the hatch assembly can be prised away from the roof panel. This hatch was lifted off easily because the seal was so poor, but often they can be difficult to remove. Don’t use metal implements (screwdriver, scraper etc.) because they’ll damage the roof. Instead use a plastic chisel or a bevelled edge strip of perspex to break the seal and to gently prise the hatch off.

2. CLEAN UP THE SILASTIC

Cleaning up contact surface with plastic wheel

Then it’s time to clean up the old seal and/or silastic, first applying wax and grease remover to soften the remaining seal and then either a plastic scraper or a nylon brush drill attachment. A final wipe over with wax and grease remover and the roof is ready for the new hatch.

3. SAND NEW HATCH

Sanding new hatch plastic so that silicon will key into surface

The hatch needs to be prepped, firstly by sanding the smooth plastic so it’s rough enough for the silastic to bond to it. The fascia covering the hatch surround on the ceiling will also probably need to be trimmed.

4. ADD TIMBER BRACING

Fitting timber bracing between roof and interior lining

This conversion didn’t have any reinforcement bracing between the roof panel and the ceiling ply lining so to ensure that the new hatch remained watertight, timber bracing was added.

5. ADD SILICON TO NEW HATCH

Applying non-acidic silicone to hatch

Now silastic can be added to the new hatch. We’ve used a non-acidic silastic to ensure that corrosion is kept at bay. The trap here is to not use enough silastic – the excess can be wiped off and if you use to little then it can come back to bite you with further water leaks.

6. PLACE HATCH ON ROOF

Hatch is placed over aperture

The hatch is placed on the aperture on the roof and gently pushed down so that the silastic makes a good seal.

7. SCREW HATCH IN PLACE

Hatch is secured with stainless steel screws

Then the roof can be secured with, in this case, stainless steel self-tapping screws. Stainless screws don’t rust and so again help to avoid corrosion.

8. REMOVE EXCESS SILICON

Excess silicone removed

Then the excess silastic is wiped off, first spraying a detergent/water mix so that the silastic excess is more easily removed and doesn’t stick to the surrounding roof panel.

9. FIX FASCIA TO CEILING

Hatch fascia secured to ceiling panel

Finally, the fascia is secured to the ceiling with self-tapping screws.

 

This article is courtesy of Caravan World. For the full article, please visit https://www.caravanworld.com.au/features/1610/how-to-replace-a-roof-hatch

 

MEET THE AUTHOR

Phil-Lord

Philip Lord

Phil is a long-term vehicle tow-tester and also the former owner of a 1979 Viscount Grand Tourer, which he restored before selling it to make room for his next project: a mid-1980s Windsor Windcheater.

Phil has been a motoring writer for more than 20 years. He has tackled most automotive and technical subjects throughout his media career, which has seen him contribute to such illustrious journals as Caravan World, Camper Trailer Australia, Wheels, 4X4 Australia and Motor.

 

RECENT ARTICLES

ebook library

ebook - Upgrade Your Caravan

Our collection of eBooks are a valuable resource for any novice or experienced caravan holiday-maker.

JOIN US

To receive regular towing hints, tips sign up to our newsletter today! Without A Hitch is the place you can turn to for up-do-date information.

For access to our collection of eBooks, simply sign up to Without a Hitch and we will send you access to our online library;

ALREADY SIGNED UP? ENTER YOUR EMAIL & WE'LL SEND YOU ACCESS TO OUR eBOOK LIBRARY

NEW TO WITHOUT A HITCH - JOIN US

To receive access to our eBook library, regular towing hints, tips sign up to our newsletter today! Without A Hitch is the place you can turn to for up-do-date information.